leaguehasem.blogg.se

Icom ic-208h programming software download
Icom ic-208h programming software download











icom ic-208h programming software download
  1. #Icom ic 208h programming software download manual
  2. #Icom ic 208h programming software download Pc
  3. #Icom ic 208h programming software download license
  4. #Icom ic 208h programming software download windows 7
  5. #Icom ic 208h programming software download download

It is far easier to use a PC, data cable and programming software to perform this function. Programming memories, whether from the front panel or mic buttons, is cumbersome.

#Icom ic 208h programming software download manual

It's the first rig I've owned where I've had to consult the manual to set the op freq and use the scanning feature. The worst of them is the general difficulty in basic operation. I have just two complaints about the 208H.

icom ic-208h programming software download

I'll suggest this is the price paid for the extremely broad receiver bandwidth, which may be a nice feature on a spec sheet though I suspect is rarely used by most owners. The rig makes rated max power on both bands, but it'd be nice if it had a 4th, extra-low power selection, perhaps 500mW, to conserve battery power in extended mobile/portable operation.Īs has been noted by others, the receiver is prone to intermod, but in most cases the attenuator function engaged by advancing the squelch control into the last 1/4 of its rotation is sufficient to suppress the intermittent intrusions of extraneous noise. The internal speaker is quite good considering its small size. The transmit audio is always complimented in simplex service- the local 2m & 70cm repeater has comparatively poor audio fidelity. At worst, they contribute a 'cheap' feel to the rig which is wholly undeserved considering the brick-solid construction of the rest of the rig. I agree with several other posters that the volume & squelch pot shafts have a excessive amount of lateral play, but this doesn't appear to affect their smooth and noiseless operation. This one has survived a few knocks and getting rained on briefly without complaint. I picked up a 2nd-hand 208H a bit more than a year ago with the intent of using it as the main shack 2m/70cm rig, but it has been pressed into service as an impromptu mobile on a few occasions. Great performer, durable, hard to program Separation cable screws on to the front attachment (Can't easily be removed for security) I get a lot of engine noise when used mobile

icom ic-208h programming software download

Very complicated menu and programming setup The front attachment is not so heavy duty (wobbly knobs) + The main radio is very heavy duty and solid (UK version)Įarlier 4-star review posted by GM1EXK on TX Audio is Low (apparently the FM Deviation is only set to 3.5khz from factory)Ĭan't set it to auto repeater shift in the repeater block. The Fan comes on regardless of TX power and temp and is LOUD! To check your firmware on the F9511, F9521: Press and hold P0 and P3, then switch the power on.Average or slightly better than average selectivity

  • Alternately: power-on the radio, press OK, scroll to Information on the Display, then press OK and select Firmware Info.
  • Next, press P1 to select Firm Info on the Display.
  • Press and hold P1 and OK, then switch the power on.
  • To check your firmware on the F7510/F7520: Connect the radio to your computer using the cloning cable, open the software and click Clone > Information.į5400D / F6400D (for firmware 3.6.2 or later)į7510 / F7520 (for firmware 3.6 or eariler) Non-display radios: You will need the software. The display will show the firmware version.ģ. Display Radios: Press and hold the Up Arrow and P3. To check your firmware on the F9011, F9021:ġ. Next, press P1 to select Firm Info on the Display.Īlternately: power-on the radio, press OK, scroll to Information on the Display, then press OK and select Firmware Info. To Check F52D F62D Firmware: Press and hold P1 and OK, then switch the power on. The display will show the firmware version. To check your firmware on the F50V or F60V:Ģ. See note above regarding programming cables.į50V / F60V (for firmware 3.6.2 or later)į50V / F60V (for firmware 3.6 or eariler)

    #Icom ic 208h programming software download windows 7

    Icom Cloning Cables - Please ReadĬables with a "B", can be used on Windows 10, 8, 7, Vista, and XP drivers.Ĭables NOT marked "B" can only be used on Windows 7 or earlier. We provide downloadable copies of Icom programming software for all Icom land mobile radios. The guide below outlines which Icom programming software is needed for each radio model, and the associated programming cable to use.

    #Icom ic 208h programming software download license

    Land Mobile Radios (LMR) require an FCC license to operate. Warning Be advised, serious penalties and prosecution can result from the unlicensed transmission on frequencies and equipment which require a license.  You can find installation instructions here.

    #Icom ic 208h programming software download download

    You may download your software immediately after ordering.

  • save the settings and program multiple radios.
  • set parameters such as the Time-Out-Timer, and other functions.
  • set functions for each programmable key.
  • set each channel's frequency and privacy codes.
  • #Icom ic 208h programming software download Pc

    Also know as Icom Cloning Software, this software runs on your PC under the Windows Operating System. Icom programming software allows users to set frequencies and functions within their Icom radios.













    Icom ic-208h programming software download